FP 6000Q

FP 6000Q

Tech Spec

ModelFP 6000Q
General
Number of amplifier channels4
Peak total output all channels driven6000 W
Peak output voltage per channel101 V
Max output current per channel38 A peak
Max output power (all channels driven)
2 ohms1500 W
4 ohms1250 W
8 ohms625 W
16 ohms320 W
Max output power bridged
2 ohmsNot recommended 1
4 ohms3000 W
8 ohms2500 W
16 ohms1250 W
Performance
THD 20 Hz - 20 kHz at 1 W<0.1%
THD at 1 kHz and 1 dB below clipping<0.05%
Signal to Noise Ratio>112 dBA
Channel separation (Crosstalk) at 1 kHz >70 dB
Frequency response (1 W into 8 ohms) + 0 / -3 dB6.8 Hz - 34 kHz
Output impedance @ 100 Hz32 mOhm
Gain, Sensitivity and Limiters
VPL, selectable per ch101, 83, 70, 56, 47, 38 V
VPL, when bridged 2202, 166, 140, 112, 94, 76 V
Voltage Peak Limiter mode (per ch.)Hard / Soft
Amplifier gain selectable (all channels) – rear-panel switches 223, 26, 29, 32, 35, 38, 41, 44 dB
Default gain35 dB
Level adjustment (per channel)Front-panel potentiometer, 31 position detented from -inf to
Connectors and Buttons
Output connectors (per ch.)Neutrik speakON
Input connectors (per ch.)3-pin XLR, electronically balanced
Output bridge modeA+B - Ch. A is signal input source. A+B, C+D - Ch.’s A and C are input source
NomadLink networkOn board, 2 x RJ45 connectors IN and OUT
Intelligent fans (on/off)Yes, depending on presence of output signal
Power on/off and Remote enable on/offIndividual switches on front-panel
CoolingDual fan, front to rear airflow, no filter required, temperature controlled speed
Front-panel user interface
CommonNomadLink Network; Power Average Limiter (PAL)4; Power on
Per channelSignal present / High-impedance; -10 dB and -4 dB output signal;Voltage Peak Limiter (VPL); Current Peak Limiter (CPL): Very High Frequency (VHF); High temperature; Fault; Mute
Power
Operating voltage, 230 V / 115 V nominal 3130-265 V / 65 -135 V
Minimum power-up voltage, 230 V / 115 V171 V / 85 V
Power Average Limiter (PAL) 4Yes
Soft-start / Inrush Current DrawYes / max. 5 A
Mains connector230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock
Dimensions
DimensionsW: 483 mm (19”), H: 88 mm (2 U), D: 396 mm (15.6”)
Weight
Weight12 kg (26.4 lbs)
Finish
FinishBlack painted steel chassis with black painted steel / aluminum front
Approvals
ApprovalsCE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC

Notes

  • 1: Regarding n.r. (not recommended) notes: The amplifier will be fully operational in bridge-mode into 2 ohm and high impedance (Hi-Z) loads, but due to physical constraints in the construction, the max. output power will not be significantly higher than running individual channels and therefore this mode of operation is not recommended.
  • 2: Automatic -6 dB gain compensation when bridging channels.
  • 3: Separate 230 V or 115 V versions available. Not selectable on the amplifier.
  • 4: PAL can reduce the maximum output power to keep the power supply operating safely, and/or to prevent excessive current draw tripping the mains breaker. Refer to the FP+ Operation Manual section 7.5.8 Power Average Limiter (PAL) for more information.
Loading...
X